Your cart is empty.
Your cart is empty.XRC Rock Guards are manufactured from 3/16" cold roll steel and hand crafted to insure a perfect fit every time. The rocker guard is finished in a black powder coat and can be used with rear corner guards. They fit with or without factory flares.
F
August 9, 2025
Looks good on my tj and pretty well built sliders. Paint seems pretty sturdy and should last long, time will tell. I installed it myself, very easy to follow instructions.
Customer
July 3, 2025
Very well made heavyweight rock slides looks fantastic
martin
June 19, 2025
Je le recommande et livraison a ete rapideSatisfait
Chris
June 14, 2025
The product it self seems well build and solid. However, they did not take into account that the rear hole that needs to be drilled goes the a section of the tub that is 2 layers thick. The supplied bolts are not long enough for this to reach because of this...and of course you will not realize this till after you have drilled a hole threw your Jeep LOL. Also, you have to remove all of your body mounts to install.....so if you have any body mount torque box rust/rot I would not recommend (if you spin any of the captured nuts.. your in for a huge repair to fix).
JRM
May 27, 2025
Look amazing fit perfect and extremely well built
Shawn
May 7, 2025
Delivered quickly...parts are solid!!!!
Customer
April 27, 2025
So I’ve had these for about 2years now ther in great shape but the mud and dirt that gets behind the sliders and Jeep is crazy be sure u clean good underneath or better take them off and clean then cause it will rust ur Jeep out eventually
A.Rose
April 11, 2025
These rock sliders are great. Super easy to install by your self and they look great and are real sturdy. For this price you cant go wrong. The only down fall was the package it was shipped in was all messed up. One of my rock sliders tabs that goes into the body mount was bent. i just bent it back by using a press, it worked fine. I still gave the product five stars because this could have happened due to the shipping.
Robert Ian Toms
April 4, 2025
Easy install and very rugged. Lots of compliments ☺
Ric
March 15, 2025
Good heavy duty metal, nice power coat finish, be aware you have to remove the body bolts and jack the body off the frame an inch or two to slide the bottom mount between the body and frame, two person job
Eric Camera
February 8, 2025
This i the second set of these that I have purchased and installed myself. Love them. They look great, have great protection and the step comes in handy on the trail. A little tip, I used a sharp utility knife to cut down the 3/16" on the body mounts. Rotary tools have a tendency to melt the rubber. Also, these fit perfectly with my Rugged Ridge Hurricane Fender Flares on my 98 TJ Sahara.
Ranger Gary
December 16, 2024
These are solid, and the installation is pretty straightforward, although it would be nice if they specified where the body mounts are--took me a while to realize that the "front" mount is underneath the radiator rather than on the frame rails like the other 5 (3 fat ones under either door; 2 flat ones just inboard of the frame, one forward of the gas tank and one right on the rear bumper area). Mine arrived well packaged, although somehow one had a roughly 2 inch elliptical dimple, 1/4" deep in the tube. But these are meant to be beat up, so I just took it as a bit of premature proof of serious jeeping... It is also a bit of a pain on my 2006 as the aft-most hole goes through where there are two layers of sheet metal and you have to use a 1" hole saw from the interior to enable room to tighten the nut properly. Managed it without having to remove seats but you can do a neater job if you do. Bolts are nice quality stainless steel--although they really should be blackened rather than silver to match the finish. Shiny silver just looks out of place on jeeps in my opinion. Welds were neat and workmanlike; tubes are sturdy but not quite as thick as I'd like. Powder coat is evenly applied. For the money, I think these are a pretty good deal.
Recommended Products
