Shopping Cart

Your cart is empty.

Your cart is empty.

DPTOOL Fuel Injector Remover Installer Tool for Jaguar 3.0 and Land Rover 5.0L Engines Replace 310-197

Free shipping on orders over $29.99

$24.47

$ 12 .23 $12.23

In Stock

1.Size:Injector Puller


About this item

  • Application: This fuel injector remover tool compatible with Land Rover/Jaguar 3.0 5.0 petrol engine, fit Jaguar X150, XK Series, X250(XF) and XJ models (V8 5.0lt petrol engines). fit Land Rover Discovery 4, new Range Rover, Range Rover Sport (V8 5.0lt petrol engines), replace OEM 310-197
  • Easy Remove Fuel Injector: Usually, Injectors on vehicles are very tough to pull in general , but this tool could easy remove fuel injector, Improve efficiency, save a lot of time, it's possible to remove injectors from a Range Rover without it, is a must tool for remove fuel injector
  • Exceed OEM Design: Our fuel injector remove tool improved on the basis of OEM, our design more easy to use, give auto repair engineers a better experience
  • Quality Guarante: This fuel injector remover tool made of high qualuty steel, high hardness and strong endurance to ensure that it is still intact after high-strength impact, and we offer lifetime warranty
  • Tips: Before use, please tighten the nut at the end of the slider to prevent it from slipping off during use.Hold slight downward pressure on the locking clasp as u use the slide hammer to pop the injector free,that will get better results



Product Description

Jaguar  Land Rover 3.0 5.0 fuel injector remover tool

Application

Replace Part Number: 310-197

Application Engine:

Compatible wit Land Rover/Jaguar 3.0, 5.0 petrol engine.

Application Vehicle Include:

Compatible with Jaguar X150, XK Series, X250(XF) and XJ models (V8 5.0lt petrol engines).

Compatible with Land Rover Discovery 4, new Range Rover, Range Rover Sport (V8 5.0lt petrol engines).

 Land Rover Jaguar Discovry 4 Rang Rover Sport V8 5.0 L V6 3.0L fuel incjector remover

Easy To Remove Fuel Injector

Tool length is 14.17 inches, 5.3 inches slide distance for slide hammer, weigh is 1.99 lb, whicn easy to remove fuel injector.

310-197

Perfect Fit

Accurate design and high standard testing, make tool tightly hold the fuel injector.

 Jaguar Land Rover 3.0 5.0 fuel inhector remove tool 310-197

Effortless Sliding Hammer

Made of high quality steel, not easy break. the slide hammer will help you save mucn time.

Before use, please tighten the nut at the end of the slider to prevent it from slipping off during use.


Walter
July 24, 2025
Saved time, money, reduced stress and frustration by how seamless this made the job. A MUST HAVE.
Mike Schoonmaker
February 23, 2025
Works great even on stubborn injectors,
Sergio
February 14, 2025
The tools is invaluable. It works well and I dont think it's possible to remove injectors from a Range Rover without it. Injectors on these vehicles are very tough to pull in general so some patience is required. My complaints about the tool are that I wish the length was longer or came with an adapter to lengthen the throw with the slide hammer or for a heavier weight on the hammer. Personally, I use an adapter with an air hammer and the "Texas Twister" air hammer attachment and it makes this job so much faster but you will have to disconnect the hood and put it up at 90*s. Other than that my tool worked very well and didn't seem to have any quality defects. A tip if you've never used the tool is you must hold the bottom clasp down onto the injector for a good grip to pull it out, otherwise the tool will slip off. I wish there was a locking mechanism to hold it on but this is just the way Jaguar designed the tool.
kypros christodoulides
January 18, 2025
The right tool for the specific job.
Revision
January 11, 2025
Me ayuda mucho para extraer inyectores qué están pegados
Recommended Products